Inspired by Anders de Flon 3x3 Bitmap Typeface. [wikipedia:::] 3x3 is a typeface based on a 3x3 bitmap matrix. It was created by type designer Anders de Flon, who long refused to release the typeface, due to the large type foundries' demand for only complete typefaces, which means upper and lower case characters, exclamation marks, etc. The typeface has appeared on several record sleeves; a slightly modified version appears on the cover of LFO's Sheath, designed by The Designers Republic. A similar typeface named 3x3 but not adhering to a 3x3 bitmap matrix was designed by Swiss graphic designer Marc Beekhuis in 2001. [:::wikipedia] [further informations:::] http://en.wikipedia.org/wiki/3x3 http://www.deflon.se/ http://www.dafont.com/3x3.font [:::further informations]
if you want to use this font for commercial matters. get in contact with me. the commercial use of this font is bind to a donation to any children health care in your country. I want to see the transfer voucher of the donation.
This font is a recreation of Richard Wisan's "ELITEQ.LQN" font file (c) 1990 for use with the program LQMATRIX. From Mr. Wisan's comment in the LQMATRIX documentation file: "ELITEQ.LQN: resembles Epson's resident Roman font, but slightly reduced to suit elite spacing."
LQMATRIX was a font design program for use with Epson LQ [Letter Quality] 24-pin dot matrix printers and compatibles. Created by noted linguist, anthropologist, and photographer J. David Sapir, the program had its beginnings in 1985 and was published by Jimmy Paris Software; the last known version that I have been able to find is version 4.44 (1991). Mr. Sapir included font set submissions from LQMATRIX users in some of the later updates; my version includes Mr. Wisan's file. A screenshot of the program is included in the comments section below.
While the graphics mode of dot matrix printers could print rather complex pictures, it remained extremely slow for large amounts of specialized text. By uploading an LQMATRIX font file into the printer's RAM, the temporary font could be used interchangeablely with the printer's resident ROM fonts. The result was a much faster print speed with little sacrifice in quality -- plus, one could design their own special glyphs or characters to suit their needs!
This was accomplish by a sophisticated design program included with LQMATRIX, whereby users could create and save characters or symbols on a 24 vertical by 15 horizontal grid for the ASCII locations 032–126 (although 001-127 were permitted). One could even place dots in the 14 half-positions along the horizontal.
I have cleaned-up some of the curvatures and harmonized a number of glyphs (along with outright modification of a few, like W and w), yet they still adhere to the same 24 x 15 grid. The original designs can be found beginning in the "More Latin" section. Because the characters for "left single quotation mark" and "right single quotation mark" were not present in DOS, I have "created" them here for sake of completion.
While suffering some serious fonter's block, here's another "wonky" experiment: this time, based on my "21st Century Dot Matrix" font. Random numbers were used to determine each dot's nudged position for the vertical (–½ / –¼ / 0 / +¼ / +½), and another set of random numbers for the horizontal. Each position had an equal 20% chance of placement.
On the previous "wonky" font ("Wonky Pins"), I adjusted some dots manually to be more visually pleasing, but I refrained from doing that here. Because so many dots were nudged to extreme positions (–½ & +½ vertically and horizontally) WITHOUT further adjustment, the printed text is still legible but definitely not as refined at "Wonky Pins"...
This typeface was also based on 2 sets of dots this time: one randomized set for an even number of dots across a row (6 or 8), and the other set for an odd number of dots (7). Sometimes, even dots and odd dots are used together on the same row in order to match the placement in the original design. These blocks are present in the "À" position. A slightly larger generic block in position "Á" is only present to prevent word processors from 'cutting off' dots nudged too far vertically up or down; initial test printings resulted in ½ dots being printed at those extremes.
Perhaps another "wonky" experiment will place the extreme ends at a lower chance of occurance (perhaps 10%) while the other three (–¼ / 0 / +¼) more at likely at 26.67% each. Or perhaps an even higher chance that the dot is not even nudged at all, with lower likelihoods as you move outwards to the extremes. This might alleviate the need for any manual adjustments, yet still get the point across that something... something has gone wonky with the printer...
Still dreaming of 24-pin printers...
This original 24×15 typeface is designed around the limitations presented by the near letter quality (NLQ) output of dot matrix printers (DMPs) during the '80s & '90s. Partially inspired by J. David Sapir's DOS font design program, LQMATRIX, it could have easily been created using that program back in the day.
(The "smart phone"-looking character in the À position is simply a placeholder, used as a quick reference to set vertical height lines while FontStructing.)
Clone of Dot24Pin Sans Outline.
Still dreaming of 24-pin printers...
This original 24×15 typeface is designed around the limitations presented by the near letter quality (NLQ) output of dot matrix printers (DMPs) during the '80s & '90s. Partially inspired by J. David Sapir's DOS font design program, LQMATRIX, it could have easily been created using that program back in the day.
(The "smart phone"-looking character in the À position is simply a placeholder, used as a quick reference to set vertical height lines while FontStructing.)
This is a clone of Dot24Pin Sans Outline